Magnetic Cable Management Power Brick Holder - VHB Plate (2-pack)
WARNING: VHB should be considered a "permanent" adhesive - removing VHB tape after it has been applied may cause damage to paint or other surfaces.
Magnetic Cable Management VHB Plates are an optional upgrade for standard Magnetic Cable Management plates. 3M VHB is a legend in the industry for a reason - their adhesive is second to none. We always recommend screwing your plates into your desk or wall for maximum hold, but if you insist on only using an adhesive solution... VHB is the way to go.
Includes:
- 2 Power Brick Holder VHB Steel Plates
HOW TO INSTALL
- Clean your mounting surface with 70% isopropyl alcohol or soap and water solution to remove any dirt or oil that may interfere with the adhesive backing.
- Peel the backing layer off a loose plate (or magnetically connected plate and arch) to expose the adhesive.
- Press the plate (or connected plate and arch) against the surface in the desired location.
- Apply firm pressure to the plate or arch against the mounting surface for at least 10 seconds.
- For maximum security, screw your plate into your mounting surface with the included screws.
- For more detailed installation instructions, please refer to 3M's installation documentation here.
If you used a Magnetic Arch to help position your adhesive plate:
-
Carefully remove the arch from the plate (Tip: reaching inside the arch to hold the plate against the surface while sliding the arch sideways can be helpful)
- Ensure good contact between the entire plate to the mounting surface by firmly pressing all areas of the plate against the mounting surface.
Disclaimer: This only comes with the VHB plates for the Power Brick Holders. Power Brick Holders are sold separately. See "Related Products" below.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Magnetic Cable Management Power Brick Holder - VHB Plate (2-pack)
Magnetic Cable Management Power Brick Holder - VHB Plate (2-pack)
WARNING: VHB should be considered a "permanent" adhesive - removing VHB tape after it has been applied may cause damage to paint or other surfaces.
Magnetic Cable Management VHB Plates are an optional upgrade for standard Magnetic Cable Management plates. 3M VHB is a legend in the industry for a reason - their adhesive is second to none. We always recommend screwing your plates into your desk or wall for maximum hold, but if you insist on only using an adhesive solution... VHB is the way to go.
Includes:
- 2 Power Brick Holder VHB Steel Plates
HOW TO INSTALL
- Clean your mounting surface with 70% isopropyl alcohol or soap and water solution to remove any dirt or oil that may interfere with the adhesive backing.
- Peel the backing layer off a loose plate (or magnetically connected plate and arch) to expose the adhesive.
- Press the plate (or connected plate and arch) against the surface in the desired location.
- Apply firm pressure to the plate or arch against the mounting surface for at least 10 seconds.
- For maximum security, screw your plate into your mounting surface with the included screws.
- For more detailed installation instructions, please refer to 3M's installation documentation here.
If you used a Magnetic Arch to help position your adhesive plate:
-
Carefully remove the arch from the plate (Tip: reaching inside the arch to hold the plate against the surface while sliding the arch sideways can be helpful)
- Ensure good contact between the entire plate to the mounting surface by firmly pressing all areas of the plate against the mounting surface.
Disclaimer: This only comes with the VHB plates for the Power Brick Holders. Power Brick Holders are sold separately. See "Related Products" below.
Original: $4.36
-65%$4.36
$1.53Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
WARNING: VHB should be considered a "permanent" adhesive - removing VHB tape after it has been applied may cause damage to paint or other surfaces.
Magnetic Cable Management VHB Plates are an optional upgrade for standard Magnetic Cable Management plates. 3M VHB is a legend in the industry for a reason - their adhesive is second to none. We always recommend screwing your plates into your desk or wall for maximum hold, but if you insist on only using an adhesive solution... VHB is the way to go.
Includes:
- 2 Power Brick Holder VHB Steel Plates
HOW TO INSTALL
- Clean your mounting surface with 70% isopropyl alcohol or soap and water solution to remove any dirt or oil that may interfere with the adhesive backing.
- Peel the backing layer off a loose plate (or magnetically connected plate and arch) to expose the adhesive.
- Press the plate (or connected plate and arch) against the surface in the desired location.
- Apply firm pressure to the plate or arch against the mounting surface for at least 10 seconds.
- For maximum security, screw your plate into your mounting surface with the included screws.
- For more detailed installation instructions, please refer to 3M's installation documentation here.
If you used a Magnetic Arch to help position your adhesive plate:
-
Carefully remove the arch from the plate (Tip: reaching inside the arch to hold the plate against the surface while sliding the arch sideways can be helpful)
- Ensure good contact between the entire plate to the mounting surface by firmly pressing all areas of the plate against the mounting surface.
Disclaimer: This only comes with the VHB plates for the Power Brick Holders. Power Brick Holders are sold separately. See "Related Products" below.
